75 monza project car

Tell everyone about the progress of your project! Please respect people's threads.

Moderator: Moderators

Re: 75 monza project car

Postby sportster96blk » Mon Mar 12, 2012 2:20 am

well i hooked up my cheater system, did not get to run it because of weather which i'm glad because i dont think my fuel line is big enough to handle the extra draw the gauge drops down to around 3lbs and needs to be steady around 5 or 6lbs though the shot which could last for most of the 1/8 mile so i ordered a separate fuel line to feed the kit my fuel sump has two ports one i just blocked off. so i'm going to run 4an line to an electric fuel pump then to the regulator its only job to feed the nitrous.........
User avatar
sportster96blk
 
Posts: 497
Joined: Wed May 27, 2009 12:41 am
Location: kenmore wa

1975 Chevrolet Monza 2+2


Re: 75 monza project car

Postby Fasterthansome » Mon Mar 12, 2012 7:21 am

What fuel pump and what size line is on the car?
STRAIGHTLINE RACING
Home of the world's quickest stock suspension H-body
Fasterthansome
 
Posts: 749
Joined: Tue Jul 11, 2006 8:58 am

Re: 75 monza project car

Postby sportster96blk » Mon Mar 12, 2012 2:59 pm

the one running my engine is a 110 gph mechanical holley with 3/8 fuel line split into two an-6 lines to a qwick fuel 750 carb.the electric pump is a jegs 130gph that my car cant run all the time because of the amps it draws is to much for my car. i should be able to run it while im spraying because its a short time on and can be switched off after the run . that way im for sure going to have enough fuel to the engine and the nitrous all the time.....george
User avatar
sportster96blk
 
Posts: 497
Joined: Wed May 27, 2009 12:41 am
Location: kenmore wa

1975 Chevrolet Monza 2+2

Re: 75 monza project car

Postby sportster96blk » Tue Jan 29, 2013 1:19 pm

Well after a few season at the track I must once again change my little car. I've stepped up to 210 full compition afr heads 650lift roller cam,comp lightwieght roller rockets.110 walled smithbrothers push rods and afr plasic composite intake after vavles were checked for clearances they did not work. pistons needed shaved.I'm waiting to get the pistons back today I hope
You do not have the required permissions to view the files attached to this post.
User avatar
sportster96blk
 
Posts: 497
Joined: Wed May 27, 2009 12:41 am
Location: kenmore wa

1975 Chevrolet Monza 2+2

Re: 75 monza project car

Postby sportster96blk » Tue Jan 29, 2013 4:51 pm

Pistons are done clearances are around 125.000 should be enough
You do not have the required permissions to view the files attached to this post.
User avatar
sportster96blk
 
Posts: 497
Joined: Wed May 27, 2009 12:41 am
Location: kenmore wa

1975 Chevrolet Monza 2+2

Re: 75 monza project car

Postby CableDroid » Sat Feb 07, 2015 6:20 pm

Updates?

My '75 is the same color too. Only other one I have seen is yours.
-Cable
'75 Vega GT Drag LS Turbo Project
CableDroid
 
Posts: 62
Joined: Thu Feb 06, 2014 10:55 am
Location: Jackson, Ca

1975 Chevrolet Monza Spyder

Previous

Return to Project Journals

Who is online

Users browsing this forum: No registered users and 5 guests