The Official H-Body Internet Community
Vega, Monza, Sunbird, Astre, Starfire, Skyhawk
75 monza project car
Moderator: Moderators
Re: 75 monza project car
by sportster96blk » Fri Feb 11, 2011 1:28 am
got my battery box installed with my on/off switch and when i was cutting the ground i cut it one inch too short
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Fri Feb 11, 2011 1:33 am
got my crank balanced and it will be back to the shop tomorrow and then they can finish the build I'm very happy..lots of last minutes details to finish before i can fit my new engine.... 
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Sat Feb 12, 2011 2:51 am
well got the battery box finished and wired in. its good to go......... 
You do not have the required permissions to view the files attached to this post.
Last edited by sportster96blk on Sat Feb 12, 2011 1:06 pm, edited 2 times in total.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Sat Feb 12, 2011 2:56 am
crank back from ballancer, work started i can wait
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Sun Feb 13, 2011 1:29 am
got the interior installed today looks hot with 5 point harness
You do not have the required permissions to view the files attached to this post.
Last edited by sportster96blk on Tue Feb 15, 2011 2:08 pm, edited 1 time in total.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Mon Feb 14, 2011 11:29 pm
got more engine work done today
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Mon Feb 14, 2011 11:30 pm
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Mon Feb 14, 2011 11:32 pm
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Mon Feb 14, 2011 11:35 pm
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Wed Feb 16, 2011 2:08 am
slow progress today had to fit the rings put bearing in rods
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Wed Feb 16, 2011 2:10 am
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Thu Feb 17, 2011 2:35 am
more slow progress but its ready for paint tonight heads tomorrow then fit push rods then intake then its oil it up see if it has pressure then take it home for install
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Thu Feb 17, 2011 2:37 am
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Thu Feb 17, 2011 2:40 am
more pics
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Re: 75 monza project car
by sportster96blk » Thu Feb 17, 2011 6:18 pm
got the heads on today now we are waiting to get thicker intake gasket and 79 length push-rods wont get engine till monday
You do not have the required permissions to view the files attached to this post.
-
sportster96blk - Posts: 497
- Joined: Wed May 27, 2009 12:41 am
- Location: kenmore wa
1975 Chevrolet Monza 2+2
Who is online
Users browsing this forum: No registered users and 83 guests